BUILT BY EXPERIENCE
The same employees have been building our grain augers for 20 plus years. If that doesn’t suggest expertise, we don’t know what does.
Now, let’s get down to the nitty-gritty.
This bin sweep works to the floor of about 1/4 revolutions and the balance of grain is removed in one to two revolutions. A stabilizer wheel comes standard on 8″ sweeps in 30′, 36′, 42′, and 48′ lengths, and on all 10″ lengths.
Option 1
Sweep Size: 6″
Flighting: 4″ OD x 11 Ga. Flighting
Flighting Shaft: 1.5″ OD x 1.25″ ID
Bin Sizes: 18′-36′
Option 2
Sweep Size: 8″
Flighting: 5.25″ OD x 11 Ga. Flighting
Flighting Shaft: 1.5″ OD x 1.25″ ID
Bin Sizes: 18′-48′
Option 3
Sweep Size: 10″
Flighting: 9″ OD x 3/16″ Flighting
Flighting Shaft: 2³/⁸” OD x 2″ ID
Bin Sizes: 30′-75′
Option 1
Sweep Size: 6″
Hopper Size: 20.5″ x 20.5″ x 12″ Deep
Tube: 6″ OD x 16 Ga. Galv.
Unloading & Sweep Flighting Assembly: 5¹/⁴” OD x 11 Ga. Flighting on 1.5″ OD Shaft
Bin Sizes: 18′-36′
Option 2
Sweep Size: 8″
Hopper Size: 20.5″ x 20.5″ x 12″ Deep
Tube: 8″ OD x 14 Ga. Galv.
Unloading & Sweep Flighting Assembly: 7″ OD x 10 Ga. Flighting on 1.5″ OD Shaft
Bin Sizes: 18′-48′
Option 3
Sweep Size: 10″
Hopper Size: 20″ x 20″ x 14″ Deep
Tube: 10″ OD x 12 Ga. Galv.
Unloading & Sweep Flighting Assembly: 9″ OD x 3/16″ Flighting on 2³/⁸” OD Shaft
Bin Sizes: 30′ – 75′
Option 1
Size: 6″
Type: Drying Floor or Aeration Installation
Hopper Size: 13.5″ x 13.5″ x 13 Deep
Tube: 6″ OD x 16 Ga. Galv.
Flighting Assembly: 5.25″ OD x 11 Ga. Flighting on 1.5″ OD Shaft
Bin Sizes: 18′-36′
Option 2
Size: 6″
Type: Concrete Slab Installation
Hopper Size: 13.5″ x 13.5″ 7.25″ Deep
Tube: 6″ OD x 16 Ga. Galv.
Flighting Assembly: 5.25″ OD x 11 Ga. Flighting on 1.5″ OD Shaft
Bin Sizes: 18′-36′
Option 3
Size: 8″
Type: Drying Floor or Aeration Installations
Hopper Size: 13.5″ x 13.5″ x 13 Deep
Tube: 8″ OD x 14 Ga. Galv.
Flighting Assembly: 7″ OD x 10 Ga. Flighting on 1.5″ OD Shaft
Bin Sizes: 18′ – 60′
Option 4
Size: 8″
Type: Concrete Slab Installation
Hopper Size: 13.5″ x 13.5″ x 13 9.25″ Deep
Tube: 8″ OD x 14 Ga. Galv.
Flighting Assembly: 7″ OD x 10 Ga. Flighting on 1.5″ OD Shaft
Bin Sizes: 18′ – 60′
Option 5
Size: 10″
Type: Drying Floor or Aeration Installations
Hopper Size: 20″ x 20″ x 14″ Deep
Tube: 10″ OD x 12 Ga. Galv.
Flighting Assembly: 9″ OD x ³/¹⁶” Flighting on 2³/⁸” OD Shaft
Bin Sizes: 30′ – 75′
Option 6
Size: 10″
Type: Concrete Slab Installation
Hopper Size: 13.5″ x 13.5″ x 11.25″ Deep
Tube: 10″ OD x 12 Ga. Galv.
Flighting Assembly: 9″ OD x ³/¹⁶” Flighting on 2³/⁸” OD Shaft
Bin Sizes: 30′ – 75′
Option 1
Size: 6″ to 8″
Tube: 8″ OD x 14 Ga. Galv.
Flight Assembly: 7″ OD x 10 Ga. Flight on 1.5″ OD Shaft
Bin Sizes: 18′ – 36′
Option 2
Size: 8″ to 10″
Tube: 10″ OD x 12 Ga. Galv.
Flight Assembly: 9″ OD x 3/16″ Flight on 2³/⁸” OD Shaft
Bin Sizes: 18′ – 60′
Option 3
Size: 10″ to 12″
Tube: 12″ OD x 10 Ga. Galv.
Flight Assembly: 11″ OD x 3/16″ Flight on 2³/⁸” OD Shaft
Bin Sizes: 30′ – 75′
Option 1
Size: 6″ to 8″
Tube: 8″ OD x 14 Ga. Galv.
Flight Assembly: 7″ OD x 10 Ga. Flight on 1.5″ OD Shaft
Bin Sizes: 18′ – 36′
Option 2
Size: 8″ to 10″
Tube: 10″ OD x 12 Ga. Galv.
Flight Assembly: 9″ OD x 3/16″ Flight on 2³/⁸” OD Shaft
Bin Sizes: 18′ – 60′
Option 3
Size: 10″ to 12″
Tube: 12″ OD x 10 Ga. Galv.
Flight Assembly: 11″ OD x 3/16″ Flight on 2³/⁸” OD Shaft
Bin Sizes: 30′ – 75′
Option 1
Size: 6″
Power Unit Required: H-81 or C-802 | 8″ Units with 1.25″ ID Center Shaft
Bin Sizes: 18′ – 36′
Option 2
Size: 8″
Power Unit Required: HC-100 or C-1003 | 10″ Units with 2″ ID Center Shaft
Bin Sizes: 18′ – 60′
Option 3
Size: 10″
Power Unit Required: HC-120 or C-1200 | 12: Units with 2″ ID Center Shaft
Bin Sizes: 30′ – 75′
Option 1
Horizontal Tube: 6″
Horizontal Flighting: 5¹/⁴” OD x 11 Ga. Flighting on 1.5″ OD Shaft
Vertical Tube: 8″ OD x 14 Ga. Galv.
Vertical Flighting: 7″ OD x 10 Ga. Flighting on 1.5″ OD Shaft
14’10” or 19’10”
Bin Sizes: 18′ – 36′
Option 2
Horizontal Tube: 8″
Horizontal Flighting: HC-100 or C-1003 | 10″ Units with 2″ ID Center Shaft
Vertical Tube: 8″ OD x 14 Ga. Galv.
Vertical Flighting: 7″ OD x 10 Ga. Flighting on 1.5″ OD Shaft
14’10” or 19’10”
Bin Sizes: 18′ – 48′
Option 1
Size: 6″
Tube: 6″ OD x 16 Ga. Galv. x 18″ Long
Flight Assembly: 5¹/⁴” OD x 11 Ga. FLighting on 1.5″ OD Shaft
Bin Sizes: 18′ – 36′
Option 2
Size: 8″
Tube: 8″ OD x 14 Ga. Galv. x 18″ Long
Flight Assembly: 7″ OD x 10 Ga. Flighting on 1.5″ OD Shaft
Bin Sizes: 18′ – 60′
Option 3
Size: 10″
Tube: 10″ OD x 12 Ga. Galv. x 24″ Long
Flight Assembly: 9″ OD x ³/¹⁶” Ga. Flighting on 2³/⁸” OD Shaft
Bin Sizes: 30′ – 75′
This distributing auger series is the textbook definition of versatile. This conveying system can be utilized to fill a multiple bin installation or can be used for unloading. Because grain flow can be reversed, you can get even greater flexibility out of your system.
*Capacities (or horsepower) may vary with type and condition of grain, auger RPM, type, and amount of exposed flighting and degree of incline.
Option 1
Size: 6″
Tube: 6″ x 16 Ga. Galv.
Drive Type: Cast Iron Drive Sheave and 8″ Section Belt
Basic Length: 21′-196′
1-15 HP
Up to 750 BPH @ 340 RPM | Up to 890 BPH @ 404 RPM
Option 2
Size: 8″
Tube: 8″ x 14 Ga. Galv.
Drive Type: 3:1 Chain Reducer 10 HP Cast Iron Drive Sheave and “B” Section Belts
Basic Length: 20′-200′
1-15 HP
Up to 895 BPH @ 169 RPM | 1265 BPH @ 239 RPM | 1615 BPH @ 305 RPM
This auger series pulls grain from an intake to a single discharge without intermediate bearings, unlike the other guys.
*Capacities (or horsepower) may vary with type and condition of grain, auger RPM, type, and amount of exposed flighting and degree of incline.
Option 1
Size: 6″
Basic Length: 6′, 11′ 16′, & 21′
Tube: 6″ OD x 16 Ga. Galv.
Flighting: 5³/¹⁶” OD x 11 Ga.
Flighting Shaft: 1.5″ OD x 1.25″ ID
Drive: 14″ OD Cast Iron Sheave and “B” Section Belts
Capacity: Up to 1170 BPH
Option 2
Size: 8″
Basic Length: 6′, 11′ 16′, & 21′
Tube: 8″ OD x 14 Ga. Galv.
Flighting: 7″ OD x 10 Ga.
Flighting Shaft: 1.5″ OD x 1.25″ ID
Drive: 14″ OD Cast Iron Sheave and “B” Section Belts
Capacity: Up to 2820 BPH
The HC Series is no stranger to the custom game. Choose your pitch, extensions, and accessories to create the perfect auger to address your needs.
*Reduced pitch flighting is preferred for handling moisture grain.
*Capacities (or horsepower) may vary with type and condition of grain, auger RPM, type, and amount of exposed flighting and degree of incline.
Option 1
Size: 6″
Basic Length: 3.5′ w/ choice of pitch
Flighting: 5³/¹⁶” OD x 11 Ga.
Flighting Shaft: 1.5″ OD x 1.25″ ID
Drive: 14″ OD Cast Iron Sheave, and “B” Section Belt(s)
Capacity: Up to 1170 BPH
Option 2
Size: 8″
Basic Length: 3.5′ w/ choice of pitch
Flighting: 7″ OD x 10 Ga.
Flighting Shaft: 1.5″ OD x 1.25″ ID
Drive: 14″ OD Cast Iron Sheave and “B” Section Belt(s)
Capacity: Up to 2820 BPH
Option 3
Size: 10″
Basic Length: 6.5′, 11.5′, 16.5′, and 21.5′ w/ choice of pitch
Flighting: 9″ OD x 3/16
Flighting Shaft: 2³/⁸” OD x 2″ ID
Drive: 19″ OD Cast Iron Sheave “3V” Section Belts
Capacity: Up to 4515 BPH
Option 4
Size: 12″
Basic Length: 6.5′, 11.5′, 16.5′, and 21.5′ w/ choice of pitch
Flighting: 11″ OD x 3/16
Flighting Shaft: 2³/⁸” OD x 2″ ID
Drive: 19″ OD Cast Iron Sheave “3V” Section Belts
Capacity: Up to 8200 BPH
These augers can be used in any horizontal, inclined, or vertical position. Bulk Tank Unloaders are the practical solution for permanent installation as a bulk tank or subfloor auger. Portable applications include unloading trucks to bins, bins to trucks, or bins to mills.
*Capacities (or horsepower) may vary with type and condition of grain, auger RPM, type, and amount of exposed flighting and degree of incline.
Option 1
Size: 6″
Basic Length: 5′, 7.5′, 10′, and 15′
Tube: 6″ OD x 16 Ga. Galv.
Flighting Assembly: 5³/¹⁶” OD x 11 Ga.
Drive: 12″ OD “B” Section Pressed Steel Sheave
Capacity: Up to 780 BPH @ 45° | Up to 1040 BPH @ Horiz.
Option 2
Size: 8″
Basic Length: 10′, 15′, and 20′
Tube: 8″ OD x 14 Ga. Galv.
Flighting Assembly: 7″ OD x 10 Ga.
Drive: 12″ OD “B” Section ≤ 15′ and 14″ OD “B” Section 20′-50′
Capacity: Up to 1860 BPH @ 45° | Up to 2480 BPH @ Horiz.
Option 3
Size: 10″
Basic Length: 6.5′, 11.5′, 16.5′, and 21.5′ w/ choice of pitch
Tube: 9″ OD x 3/16
Flighting Assembly: 2³/⁸” OD x 2″ ID
Drive: 19″ OD Cast Iron Sheave “3V” Section Belts
Capacity: Up to 4515 BPH
Option 4
Size: 12″
Basic Length: 6.5′, 11.5′, 16.5′, and 21.5′ w/ choice of pitch
Tube: 11″ OD x 3/16
Flighting Assembly: 2³/⁸” OD x 2″ ID
Drive: 19″ OD Cast Iron Sheave “3V” Section Belts
Capacity: Up to 8200 BPH
*Capacities (or horsepower) may vary with type and condition of grain, auger RPM, type, and amount of exposed flighting and degree of incline.
Option 1
Size: 6″
Hopper: 19.5 L x 16″ H x 18″ W
Tube: 6″ OD x 16 Ga. Galv.
Flighting Assembly: 5³/¹⁶” OD x 11 Ga.
Drive: 14″ OD Cast Iron Sheave, “B” Section Belt(s)
Capacity: Up to 975 BPH @ 30°
Option 2
Size: 8″
Hopper: 19.5 L x 18″ H x 18″ W
Tube: 8″ OD x 14 Ga. Galv.
Flighting Assembly: 7″ OD x 10 Ga.
Drive: 14″ OD Cast Iron Sheave, “B” Section Belt(s)
Capacity: Up to 2070 BPH @ 30°
Option 3
Size: 10″
Hopper: 24″ L x 24″ H x 24″ W
Tube: 10″ OD x 12 Ga. Galv.
Flighting Assembly: 9″ OD x 7 Ga.
Drive: 19″ OD Cast Iron Sheave “3V” Section Belts
Capacity: Up to 3770 BPH @ 30°
AVAILABLE LENGTHS | RECOMMENDED FOR BIN DIAMETER | |
6″ & 8″ | 10″ | |
11′ | N/A | 21′ |
13.5′ | N/A | 24′ |
16′ | N/A | 27′ |
18.5′ | N/A | 30′ |
21′ | 21′ | 36′ |
26′ | 26′ | 42′ |
28.5′ | 31′ | 48′ |
36′ | 36′ | 60′ |